The call that started with a dead conveyor—and a gearbox tag
In March 2023, I was on the phone with a bakery maintenance manager while standing in a wash-down area that smelled like yeast and hot grease. A conveyor had stopped mid-shift. The motor was hot, the gearbox was leaking, and the production line was backing up.
I've been handling motor and drive replacement orders for 11 years, first as a maintenance planner and now on the distributor side. I've made my share of expensive mistakes. This one cost about $1,180 in replacement hardware, plus downtime I'd rather not calculate. It also changed how I use every Leeson motor wiring diagram pdf I download.
The conveyor had a Leeson single-phase motor bolted to an old gear drive. The gearbox tag read Pete Jackson. I typed 'what happened to pete jackson gear drives' into Google while the manager was still talking. I got forum threads, old catalog pages, and no clear answer.
I don't have hard data on the exact corporate timeline—whether the line was absorbed, discontinued, or just became hard to source. What I did know was that a new gear drive was six weeks out. The motor was the urgent part. So we decided to keep the gearbox and replace the motor only.
That sounded simple. It wasn't.
The downloaded diagram that looked right (the first mistake)
We ordered a 1.5 hp Leeson single-phase motor with a capacitor start, dual voltage, and a 56C frame. The nameplate was painted over, but the model prefix matched the old unit. I downloaded a 'leeson motor wiring diagram pdf' from a forum thread because the official page wasn't loading on my phone. The drawing looked official. The terminal numbers looked plausible. That was enough for me—which is exactly how small mistakes start.
I should have opened the terminal cover first. The motor's own connection diagram was printed inside, but the cover had been painted over during a previous washdown repair. I didn't think to scrape it. I trusted the PDF instead.
We used a 'leeson single phase motor wiring diagram' from that PDF to set the links and capacitor leads. The motor started. Then it ran backward. We swapped two leads. It started again, ran for about 40 seconds, and the start winding let go (ugh).
That's when I compared the downloaded PDF and the motor nameplate side by side. When I compared the downloaded diagram and the nameplate diagram side by side, I finally understood why the terminal numbers didn't line up: the PDF covered a different terminal board revision. Same brand, same horsepower range, different internal connections. The drawing wasn't wrong. I was using it on the wrong motor.
The lesson wasn't 'PDFs are bad.' The lesson was that a PDF without the exact model and serial match is just a guess with a nice font.
The turn: what it cost, and the quote that wasn't transparent
We pulled the motor and got two quotes. A local shop offered a rewind for $420. Another vendor quoted $1,180 for a replacement motor with expedited freight and a startup check.
I went back and forth between the two for a day. On paper, the rewind made sense. The gearbox was old, the budget was tight, and the motor frame was standard. But my gut said something was off about the cheap quote. The shop was slow to answer basic questions about load testing and warranty.
Every spreadsheet analysis pointed to the rewind. Something felt off. Turns out my gut was picking up on the missing details: the $420 quote didn't include pickup, delivery, load testing, or a warranty beyond 30 days. By the time I asked 'what's NOT included,' the total was closer to $890—with a week of downtime. The $1,180 quote listed freight, tax, and a startup check. I picked the transparent quote. It stung, but it was the cheaper total cost.
The invoice I remember was $1,180 for the replacement motor and expedited freight. I want to say downtime cost another $600 in lost production, but don't quote me on that split. The bakery lost two production days—or rather, three once the electrician could get back.
That was the second lesson: a low price with hidden extras isn't a low price. I've learned to ask what's NOT included before I ask what's the price.
What I changed in my process (and where the induction motor diagram fits)
After that job, I built a pre-install check that I now use on every motor replacement, especially when the old nameplate is damaged.
- Match the exact model and serial number to the wiring document—not just the horsepower and frame.
- Open the terminal cover and photograph the printed connection diagram before touching any leads.
- Download the official PDF from the manufacturer's site when possible, and save the revision date.
- Check voltage links and capacitor connections against the nameplate, not against a forum post.
- Photograph the nameplate, terminal board, and gearbox tag before disconnecting anything.
I also started keeping an induction motor diagram in the job packet for every single-phase replacement. The induction motor diagram isn't decoration; it shows the start/run winding relationship and capacitor connections in a way that makes the terminal board less abstract. If the diagram and the nameplate disagree, I stop and call the manufacturer. Ten minutes on hold is cheaper than a smoked winding.
We did look at brushless dc motors for the next conveyor upgrade. On paper, brushless dc motors offered better efficiency and speed control. But the existing controls were 115 V single-phase, the washdown environment was harsh, and the gearbox ratio was built around the old motor's speed. We stayed with an induction motor and corrected the wiring. That was a scope decision, not a knock on brushless technology.
Per NEMA MG 1, motor nameplates and connection markings are supposed to give you the information to connect the motor correctly. I now ask vendors to point me to the exact nameplate data and the matching connection diagram—not just a generic PDF. If they can't, I treat that as a warning sign.
The checklist I use now
Here's the short version I keep taped inside my job folder:
- Read the nameplate before you read the PDF.
- Photograph the terminal cover diagram before you remove a single wire.
- Confirm the PDF revision matches the motor revision.
- Ask the vendor what's NOT included in the quote.
- If the gearbox tag is obsolete, measure the ratio and mounting pattern before ordering a motor.
If the diagram doesn't match the nameplate, stop. Don't guess. The ten minutes you save are not worth a $1,180 motor and three days of downtime.
This was accurate as of Q1 2025. Motor lines and gear-drive support change fast, so verify current availability and wiring documents before you order.
And if you're searching 'what happened to pete jackson gear drives' because you're staring at an old tag like I was, don't stop at the first forum answer. Get the gearbox ratio and mounting dimensions measured, then match the motor to the actual load. The motor is only half the drivetrain. The other half is the paperwork you didn't check.

Leave a technical comment